Blister machineManufacturer: blister machine maintenance:

  Features of automatic continuous vacuum suction machine:

Automatic blister machine manufacturers

  1Cooling system: equipped with Japanese MeijiA-100sprinkler head10Only, Riling3Pi Chiller1Table, mold tray water transport, equipped2A powerful fan, and the air inlet of the fan is designed as an air duct to avoid sucking in the loop hot air.

Vacuum Pump Principle of Blister Machine

  22. Receipt area: the material receiving box is designed to be movable, with manual gear transmission, pneumatic pressing and placing, and fine screw transmission and slicing.

What are the selection of blister machine

  3, vacuum system: German Richle or Puxu vacuum pump, power4kw, the pumping speed is per hour150-160m3, the vacuum cylinder is0.25m3.

  4All functions: secondary vacuum function, vacuum delay function, upper mold buffer function, upper mold electric adjustment function, lower mold electric adjustment function, multiple blowback function, multiple demoulding function, shift production metering function, secondary upper mold function, upper mold isolation function, delayed water spray function, delayed blowing function, blowing isolation function, secondary independent upper mold function, automatic exit function of electric heating furnace, push-pull adjustment function of middle and lower brakes, motor feeding setting function, bottom air delay function.

Blister Machine Blister Mold Technology

  5Control system: artificial intelligence, the system adopts SiemensCPU224Host and SiemensEM222Module, man-machine interface adopts Delta10.4Inch color touch screen, professional operation screen, corresponding to the common operation method, to solve the problem of upgrade control. Powerful memory space, set up including automatic operation, manual operation, function settings, mechanical animation, fault display, equipment documentation, safety guidelines and other interfaces, the whole system is safe and stable.

  6Forming area: forming length1220mmUnlimited inside, forming width470~720mm, the die plate is aluminum alloy water transport type5Block, independent disassembly, design of fast vacuum tube and water pipe joints, easy to change the mold plate, mold plate each.50mmWidth of a specification, the largest molding height200mm, sheet application width510~760mm, bottom mold cylinder150×350mm, The height can be adjusted electrically, and the die plate stroke is the largest320mm, And equipped with vibration demoulding, multiple demoulding blowing, demoulding blowing delay function. Upper mold cylinder125×450mm, can electrically adjust the stroke, and is equipped with secondary upper die independent, upper pressure demoulding isolation function, lower gate and middle gate are designed with fast push-pull type.

  71. Chain rail drive: the chain rail cover plate is imported718The steel is made of special fine processing, and the middle plate and the lower plate are made of domestic high quality.45#Steel fine processing, high docking precision, low friction coefficient, long service life, pull the use of variable frequency control technology, with the encoder, input the required length, pull the fast and accurate.

  82. Feeding area: the feeding is lifted by motor, and the weight can reach200Kilograms, the feeding sheet to be fed is driven by a rubber curtain, and two large material rods are provided for changing the sheet.

  9Electric heating area: the electric furnace is made of stainless steel, Taiwan heating tile, Japan high temperature wire, high control porcelain joint, and upper furnace60Block heating tile, lower furnace42Block heating tile, maximum power40.8KWSouth KoreaDPCThe digital proportional regulator controls and adjusts the temperature one by one, and is attached with a temperature sensor to display the temperature of the electric furnace, which is convenient for data management. Electric furnace cylinder drive, power failure or overhaul electric furnace out of the machine, safe and convenient.

  13. Regularly inspect the amount of oil in the oil mist device of the blister machine, and adjust the amount of oil in a timely manner. When the new machine is used, it can be adjusted to a greater extent to ensure sufficient lubrication for all pneumatic components.

  2The water filter in the air circuit of the plastic suction machine shall be released once per working shift, and the oil mist device shall be frequently refueled to ensure the normal operation of the solenoid valve and the cylinder.

  3The blister machine shall be kept clean and sanitary, and the surrounding sundries and dirt in the machine shall be removed after shutdown.

  4The sliding guide posts, bearings and sprockets of the blister machine must be maintained in a good lubrication state and lubricated frequently.

  5Each working shift of the blister machine should first check the oil level of the vacuum pump; The vacuum pump oil should be replaced once a month.

SHENZHEN YONGHENGSHENG MACHINERY MANUFACTURING CO., LTD16Over the years has been committed to research and development to provide Shenzhen blister machine, Shenzhen bubble shell machine, Shenzhen vacuum blister machine, Shenzhen thick sheet blister machine, Shenzhen blister forming machine, Shenzhen thermoplastic forming machine,blister machine hot line:0755-84817776